Lydia has fitted a brand new set of green carpets in the Austin Devon Pickup.
Jonn secured all track rod ends on our 1959 Austin Healey 3000 and tightened the ball joint before fitting a new split pin. With the steering components addressed, he lowered the car to the floor and confirmed that the tracking remained correctly set, with plans to check it again following a road test. He then […]
Jonn carefully applied heat to the steering wheel of our Morgan 4/4 in order to remove it. Once removed, he turned the wheel to the left and refitted it to correct the alignment. An initial test was carried out around the yard, followed by a run up the road, both confirming that the steering wheel […]
Jonn brought the Rover Vitesse into the workshop and jacked up the vehicle to remove the front wheels. On the offside, he stripped out the track rod end, which was found to be seized in place. To resolve this, he cut off the track rod end and removed it, then applied heat to the track […]
Kickboards have been made and fitted. to our 1951 Austin Devon Pickup.
Jonn hoovered out the interior of our 1984 Morgan 4/4 before refitting the driver’s seat. To ensure the seat was securely installed and to distribute the load more evenly, repair washers were fitted beneath the floor. He then removed the gear lever to investigate further issues, during which he found remnants of a broken bush. […]
Jonn investigated a rattle coming from the offside rear of our 2007 Porsche 911 and identified the backplate as the source. He removed the wheel and calliper, then de-adjusted the handbrake shoes to allow for the removal of the disc. With the disc off, he cleaned the handbrake shoes and inspected the dust shield, which […]
Jonn has addressed an issue with the steering column lower bush on our 1987 Rover Vitesse. He began by undoing the securing plate at the bulkhead, then proceeded to clean the splines on the steering shaft and slacken the universal joint. The shaft was knocked down, and alignment marks were made on the splines to […]
Some interior pieces can finally be fitted to our 1976 Jensen Interceptor without being in anyone else’s way. Carpet side pieces are in, and under-seat runners are covered in vinyl.
The boot lid has been refitted to our 1955 Aston Martin DB2/4 Drophead Coupe.
Ben has been assembling various components for the suspension, cleaning threads and fitting bushings on our 1969 Aston Martin DB6 Volante. He built up the new koni shock absorbers and started fitting, but further checks showed these should be black, even though our Aston Martin parts company supplied red units. So these were removed and […]
The rear brake wheel cylinders were corroded and leaking on our 1966 Volvo Amazon, so they were replaced along with the O/S metal brake pipe, as it was seized in the old cylinder.
The engine bay of our 1967 MGB Roadster has been prepped, had epoxy primer applied before being painted.
The spare wheel well and boot floor have been prepped and welded in on our 1978 Mercedes 350SL. Spot welding was completed in factory spots and dressed back. Towing eye fabricated and welded in factory position. Preparation for further panel work.
Jonn has been working on our 1959 Austin Healey 3000 by removing both carburettors from the engine. Each unit was then stripped down, thoroughly cleaned, and blown out to remove any residual debris or buildup. Following this, the carburettors were carefully rebuilt with attention to detail, ensuring all components were correctly reassembled. Lubrication was applied […]
The rack mounts and parts of our 1969 Aston Martin DB6 Volante, which Ben anodised, like the shims that set the suspension geometry, are seen in the pictures below. The new bering races have been pressed into the hubs and then a coat of paint after masking up otherwise the paint would likely have been […]
Jonn carried out work on our 1959 Austin Healey 3000, beginning with the installation of a new offside front wheel bearing. He fully greased and adjusted the bearing, then refitted the wheel and conducted an initial test. After removing the wheel to readjust the bearing, he refitted and tested it again, confirming it was operating […]
The wheel arch of our 1951 Austin Devon has been painted ready to go back onto the car.
Our 1959 Austin Healey 3000 has been getting some attention in the Bridge Classic Cars paint shop.
Both colours needed reworking on the inner boot lip of our 1973 MGB Roadster.
Today Pete has brought the body into our workshop and removed it from its transport trolly, it’s been safely put onto our two poster ramp ready for fabrication work to start. In the meantime Pete and our photographer Nick have taken a wealth of photos of all the areas we can access that need repair […]
Work has begun on aligning the radiator brackets and working out how both radiators fit on our 1987 Maserati BiTurbo..
Jonn continued repairs on our 1997 Mercedes 280SL by inspecting the offside front fog light. He confirmed the bulb was intact and the fuses were in working order. After cleaning the connector, the light functioned correctly, and he then refitted the arch liner. Moving to the centre air vents, he removed and stripped them, reattaching […]
The old vinyl hood was removed from our 1979 MGB Roadster. It was replaced with a new double-duck canvas type one instead.
Various pieces of carpet from our 1976 Jensen Interceptor have been removed and replaced. The rear panel under the window was also taken out and a new one was made from cardboard and then covered in leather
Our 1959 Austin Healey 3000 has been having some repairs completed on its bodywork.
Jonn attended to the insecure driver’s door card on our 1997 Mercedes 280SL by stripping and removing the panel. Upon inspection, he found that the top of the panel was damaged where it should fit into the weather strip clips, and two fixings were missing. He removed the weather strip and repositioned the clips along […]
The past couple of days have been spent getting the hard-to-reach areas of our 1969 Aston Martin DB6 Volante back to bare metal. There was a lot of old paint on the car, with layers of filler in damaged areas where previous repairs had been carried out. In the areas where rust was present, this […]
Jonn carried out a recheck of the valve clearances on our 1968 Lotus Cortina and replaced the cam cap nuts with new nyloc nuts, torquing all caps to 9 lb/ft. He then cleaned the rocker cover, secured the gasket in place, refitted the cover, and torqued it to 7 lb/ft. After running the engine, he […]
Our paint and body manager Chris has been working his magic on the 1953 Aston Martin DB2/4 which is currently undergoing its ground up restoration by the Bridge Classic Cars team at our Suffolk HQ. Chris is going all the way through the bodywork of the car, gently refining it with the use of minimal […]