classic car restorations

Down to It – Working on the Steering Coupler of the 1968 Jaguar MkII 2.4

The next job to be done on the 1968 Jaguar MkII 2.4 by Bridge Classic Cars is to replace the steering coupler. This will help to tighten up the loose steering for its owner.

This job is being done by our master tech, Dave. Dave has a huge wealth of knowledge and experience working on classic cars so a job as delicate and crucial as this was given to him. Carefully, Dave began by removing the shaft from the coupler in order to gain access to the bushes and balls inside the steering box. As opposed to some MkII’s that we have worked on in the past, this MkII remains as a steering-box car.

After removing the original parts from the car, Dave began to check the new replacements would work with the car and were correct. Then, it was a case of getting everything back together and into the car. Dave took his time to make sure that every component cleared the steering box and its boot so it remained happy for many years to come.

After the job was complete, Dave manually checked that the box rotated as it should and also meshed together with as little play as possible thanks to the new parts.

There will be more updates soon as work continues on this stunning MkII 2.4.

Wheel of Fortune – Refinishing the Wheels of the 1968 Jaguar MkII 2.4

One of the jobs to be done on the 1968 Jaguar MkII 2.4 was to paint the wheels to a colour matched off white, just the same as the body. So, it was off to the paint shop under the watchful eye of our in-house paint expert Alan.

Finished in a healthy layer of primer, to begin with, the wheels were then prepared to be put in the booth ready for painting. Alan used our state of the art paint mixing computer to find the closest match possible to the existing paint of the MkII in order to get the best match.

Then, with the right amount of paint mixed up and in the gun, it was time to start laying down the first of many coats to get these wheels to look perfect. Alan took his time to make sure the paint fell evenly and was given enough time in-between coats to achieve the best results straight out the gun. And, as you can see the results are absolutely incredible.

Seamlessly – Repainting the Rear Valance on the 1968 Jaguar MkII 2.4

The 1968 Jaguar MkII 2.4 has been in the Bridge Classic Cars in-house paint shop where our paint expert Alan has worked his magic on the rear valance.

The valance had been coated with a thick black stone chip protection across the lower parts, so Alan pulled out his trusty DA sander and got to work. Carefully knocking back the stone chip, Alan exposed the paintwork underneath. Because of the thickness of the protection, Alan had to take it back quite a way. Once the area had been thoroughly cleaned down and smoothed out, Alan could begin his detailed and meticulous work.

Carefully, Alan applied the new stone chip to the area to protect the car from any possible marks or damage while it’s being enjoyed by its very lucky owner.

After the area around the new stone protection had been masked off, Alan carefully colour matched a small amount of paint to the rest of the car in order to seamlessly blend the new area into the existing rear panels and behind the rear bumper.

Coming Soon – 1974 Pontiac Trans Am Firebird

Coming soon to the Bridge Classic Cars workshop is this incredible 1974 Pontiac Trans Am Firebird.

It seems that recently we’ve been seeing a fair amount of classic American muscle cars! This Trans Am Firebird will be coming into us for some interior jobs to be carried out for its very lucky owner as well as a couple of mechanical jobs on the bright red Muscle car.

The in-house restoration teams will go through the car and assess any other items that may require attention before starting work on the list for the owner of the car.

Keep your eyes peeled for more on the 1974 Pontiac Trans Am Firebird soon here on the Bridge Classic Cars news page.

Update: 14/05/2024 – although the works were due to start at the end of 2021, beginning of 2022, the car never came in to our workshops so none of the works we expected to carry out materialised. We have since taken a call from it’s new owner who has gone on to completely restore the vehicle. I bet it looks amazing now! Thanks for your call and hope you enjoy many years with your car.

Behind the Scenes – Photoshoot of the 1975 MGB GT V8

There’s always a buzz around a new competition car. Especially one as special as this… a 1975 MGB GT V8.

This small, V8 powered British sports car is the latest prize to be won through Bridge Classic Cars Competitions by one very lucky winner. This is the story behind the amazing photos and video of the car.

Although the winter morning was damp and the sun hid its bright rays behind grey lumbering clouds, it couldn’t dampen the spirits of the team ready to shoot the new competition car. The V8 burbled into life after it had been pushed out of The Hangar. Gently, the aluminium V8 warmed up on the tarmac. Making sure the pressures and temperatures were all correct before being driven to the South Loop, Charlotte eased the sports car into gear and pulled away from the shadow of the hangar.

The wonderful noise from the V8 wound its way through the trees in the Suffolk forest. The early morning light left the highlights across its vibrant, rich red bodywork soft but with a certain crispness from the moisture in the air. While photographing the car, you couldn’t help but fall in love with the simplicity of an MGB GT. It does however have a certain elegance and sophistication with that simplicity. The sloping back which then rolls into the bumpers that wrap around its rear and the long elegant bonnet that stretches towards the horizon but not to the scale where visible is difficult. Perfectly useable as a classic or even every day.

The interior shows the story of the car. The seats have a character to them that matches the personality of the car, they show that the car has been used and adored since its earliest days.

As the MGB moved out and Charlotte gently rolled it through the gears, the car has a majesty as it moved. A gracefulness that all MGB’s seem to have but is amplified by the low, ambling noise from its 3.5 litre V8. As the clouds grew darker and the sun drifted further and further away, it was time to take the car back to The Hangar. Ready, for it’s next lucky owner.

This 1975 MGB GT V8 could well be yours. Click the link below and enter now for your chance to win this and other dream classics with Bridge Classic Cars Competitions.

See all the Bridge Classic Cars Competitions prizes.

The Next Phase – Dash and Hood Pieces for the 1973 Jaguar E Type Series III Roadster

Brian, Kath and Lydia have been working on the next phase of the interior for the 1973 Jaguar E Type Roadster that Bridge Classic Cars calls Fern Grey. Now that the windscreen has been fitted and cured, it’s time to start getting the trim, dash and hood in place.

Using the original dash panels and A-Pillar trims, Brian stripped apart the panels ready to be recovered. The original foam for these pieces was in remarkably good condition so they were refreshed and reused. The trimming in the rich black leather however is all brand new. Brian selected a hide that compliments the rest of the interior but also matches closely what would have originally been used on the E Type’s to trim the pieces with.

Each of the panels and trims was hand-cut and finished by the Bridge Classic Cars in-house trim team to ensure the best fit. Including the dash pad which now that the windscreen is safely in place could be secured to the top of the dash after test fitting multiple times.

With all of the dash and trim around the windscreen fitted, Brian and the team began to work on getting the foldable hood mechanism in place. Checking the mounting points for the front and back of the hood, Brian began the task of gently manipulating the mounts to ensure the best possible fit as well as making sure each of the spars sat level and true. Thankfully after some skilled moving, the hood sat perfectly inside the gorgeous roadster.

La Voiture Noire – The Long Lost Bugatti

The mid to late 1930s were a heyday of Automotive design. Bespoke, futuristic interpretations of personal transport heavily influenced by art-nouveau and the art deco school of design. Elegant answers to a simple question of moving people from one place to another. One of those at the forefront of this was a small French manufacturer by the name of Bugatti.

Bugatti had risen to prominence with its massively successful, lightweight Grand Prix cars along with super luxurious elegant limousines in the 1920s and early 1930s. The founder Ettore Bugatti came from a long line of artisans and craftsmen who plied their various styles and trades to all manner of things, but for Ettore it was cars. By the 1930s, Ettore had begun to step back from his role as the man in charge of Molsheim. His son, Jean would rise through the ranks as a talented designer, engineer and driver in his own right away from his father’s shadow. Culminating in what many believe to be the most beautiful series of Bugattis ever made. The 57SC Atlantics.

Using influences from both Art Deco and Art Nouveau, the Atlantics were a new style for a new type of owner. For this new car and new owners, only 4 57SC Atlantics would be built. Each of them was heavily personalised to their owner’s tastes and styles, their story begins with a special one-off. The 1935 Aerolithe Concept. A magnesium bodied show car which was set to usher in a new era of Bugatti’s by using advanced materials and techniques to blend the worlds of Grand Prix and Grand Tour.

The 4 Atlantics would use this technique to begin their construction, however, they were soon swapped for aluminium bodies made in the same style as the Aerolithe. With the identifiable riveted dorsal fin of the concept car displayed prominently on the Atlantics. Out of those 4 cars, three are accounted for and have gone on to be concours and show winners in their own rights around the world.

The fourth was given the name ”La Voiture Noire” or, The Black Car. It had originally been used by Bugatti as the show car to demonstrate to potential customers and the world the new age of Bugatti under Jean’s leadership and also happened to be Jean Bugatti’s personal car whilst doing so. La Voiture Noire’s early history is well documented.

The cars official Bugatti name is chassis 57453 and was gifted to Bugatti factory driver Robert Benoist for winning the 1937 24 hours of Le Mans and then was later given to fellow driver William Grover-Williams before his return to England just before the outbreak of World War 2. From the outset of the war until 1941, La Voiture Noire was kept as a test car for Bugatti after the death of its master Jean in 1939 whilst testing a racing prototype. But after 1938, no official records have ever been kept of the car. This is where the ghost story begins…

Rumours have circulated for the better part of 80 years about the journey La Voiture Noir would take into its own mystery. The last records speculate the chassis number was changed to 57454 and the whole car was to be dismantled for parts to be used on other projects and what was left was to be boxed up and stored. Other stories say the complete car had apparently made its way south to Bourdeaux, possibly in an attempt to conceal the car away from the factory and the furious pass of the German Army as it began planning its march into Europe on the eve of war. Some have also said it could have been sent as far away as the Middle East to be protected under the eyes of trusted Bugatti owners. But, no evidence or any form of lead has ever been found for the resting place of the car. Rumours of deserted railway cars, french barns, bricked up buildings, fake basements and even burying the car alive have circulated over the years throughout the enthusiasts. Ghost stories and treasure tales handed down from one generation of petrolhead to another. But alas, no news.

Until recently. A mysterious post on social media revealed a very strange looking body sitting in the back of a Connecticut, USA body shop claiming to be the missing Bugatti. However, leading Bugatti experts fervently rebuke that this is in any way La Voiture Noire. It is estimated that if Chassis 57453 (or 57454 if the history is correct) were to be rediscovered somehow, it could expect to fetch anywhere north of $100 million at auction because of its importance.

But, to most diehard enthusiasts, its story remains priceless.

This Just In – 1934 Riley 9 Lynx

Bridge Classic Cars have today welcomed its latest guest to the Pettistree workshop. This 1934 Riley 12/4 Lynx has come to us all the way from South Africa where it has spent parts of its long life.

The car will be going in to be assessed by our in-house restoration teams to determine what jobs will need to be done to this classic tourer to get it into a useable and safe condition. The Riley is finished in an incredible French blue with a black interior. The 4 door tourer is a wonderful example of pre-war open-top travel in both style and comfort by a long-gone marque.

The car was cherished and used in South Africa being part of the local enthusiast groups and taking part in several classic car rallies. For now, the Bridge Classic Cars technicians will begin to reassemble the car to be able to check and confirm all parts and pieces for the 1930s tourer are there and in good order.

Expect to see more on this amazing 1934 Riley 12/4 Lynx on the Bridge Classic Cars news page.

Primed and Ready – Body of the 1955 Aston Martin DB2/4 Mark 1 Primed

Chris and the team in the Bridge Classic Cars in-house paint shop have been busy at work preparing and priming the 1955 Aston Martin DB2/4 Mark 1 for the next phase in the restoration.

Chris and the team carefully prepared each panel and part individually to make sure they were properly prepped before entering the spray booth. Each part has been given a coat epoxy primer to help seal the material beneath which has been so carefully worked on by the Bridge Classic Cars restoration teams.

With everything primed, it was time to move on to the protective coating on some of the other pieces and parts of the shell. For the most durable protection against road grime and weather, the team here use Raptor Guard. Applied to specific pieces, it helps to protect any of the pieces from moisture and is well worth using for a classic that is destined to be used and enjoyed.

Whilst the primer and the raptor guard on the shell were left to cure, Chris began to prepare and spray Raptor on some of the floor panels, the transmission tunnel and other pieces which will be exposed to the elements.

Looking Ahead Behind – Fitting the Mirror to the 1960 Jensen 541S

The restoration technicians at Bridge Classic Cars have been busy working on a couple of jobs on the 1960 Jensen 541S before it goes to The Hangar for its winter storage.

One of the most important jobs to be done was to fit a rearview mirror at the request of the owner. The mirrors for the 541’s did not come as standard, however, because of our history with their restorations, we managed to source a piece for the owners’ peace of mind while driving.

Carefully, the mirror was placed into the door at the right place after dozens of test fits to ensure the part sat properly and also looked right. The detailing on the mirror itself is a beautiful part of its story. With exposed, bright hardware and a simple flat disc but with the base coming to a sharply defined point, it looks completely at home on the 541.

There are a couple of other jobs to have a look at on Peony Red, which will you’ll be able to see about here on the Bridge Classic Cars news page.

Fine Features – Sending Parts from the 1955 Aston Martin DB2/4 for Refurbishment

The trim work on the 1955 Aston Martin DB2/4 is absolutely beautiful. Simple and elegant but there is quite a bit of it.

These are the latest pieces of the DB2/4 Mark 1 to be sent out to a local specialist for replating and polishing. This is being done to make sure that every piece of the brightwork on this stunning 1950s sportscar will be uniform and stunning. Although they may seem small, every piece of the car must be perfect to match the work the team here at Bridge Classic Cars have done on the car during its restoration.

There will be more updates very soon on the 1955 Aston Martin DB2/4 very soon here on the Bridge Classic Cars news page.

Core Components – Stripping Parts for the 1956 Jensen 541 to be Refurbished

Mauro, has been working on getting all the relevant parts and pieces of the 1956 Jensen 541 ready to be sent out to local, trusted specialists for refurbishment.

Bridge Classic Cars have a long history of restoring Jensen 541’s to a very high standard and this 1956 541 is to be no exception. The pieces of the car have been carefully dismantled down to their core components and assessed for condition and originality. Where possible, we try to keep the cars as original as possible but refinished and restored to go back on the car.

The pieces here have also been catalogued and photographed for record as well as detailed records of them being dismantled so that everything and their construction method is accounted for. Each component is dealt with individually to ensure that it safely comes apart and if not, can be taken apart and repaired to the exacting standards that Bridge Classic Cars holds its restorations to.

Soon, there will be more updates on the 1956 Jensen 541 during its restoration, so keep an eye out here on the Bridge Classic Cars news page.

Pieces of the Puzzle – Installing the Windscreen of the 1973 Jaguar E Type Series III Roadster

The windscreen of the 1973 Jaguar E Type Series III Roadster is now in the car!

This moment has been a long time coming. The curving and elegant windscreen for the E Type is like a jewel in its crown. This completely bespoke Jaguar has been cherished by the in-house restoration teams at Bridge Classic Cars throughout its build so, having one of the final aesthetic pieces complete was a true milestone.

For windscreen removal and installs, we use a local specialist called Car Glass and Trim who we have worked with for many years. Their technicians came out to install the glass into Fern Grey with the same attention to detail and care as our very own technicians. With the windscreen and its seals in place, it was time to let the adhesives cure while Kath and Brian in the trim shop carry on fitting out the E Type.

Back at It – Preparing the 1971 Jaguar XJ6 Engine and Cylinder Head

The cylinder head for the 1971 Jaguar XJ6 is back at the Bridge Classic Cars workshop. This has been away at a local specialist to be assessed and repaired ready for the car.

Some may remember that our in-house restoration teams found a large chunk of material missing from the leading edge of two valves in the front cylinder. Also, it was discovered along with this that a blown head gasket had been what caused the misfire and running issue noted on the straight-six.

In preparation, Jonn had cleaned up the entire engine block which was discovered to be completely packed with sludge in every coolant galley and water jacket. Jonn has spent hours clearing out all the debris and flushing through the engine block to ensure all is ok when the engine is finally fired up for testing.

Now, it is down to Paul to install the cylinder head on top of the straight-six. For that, he will prepare the new head gasket and double-check all tolerances before the head is finally bolted down.

Expect to see more on the 1971 Jaguar XJ6 here on the Bridge Classic Cars news page very soon.

Ready, Set, Go – Preparing to Reinstall the V8 into the 1973 MGB GT V8

Jonn, one of our in-house restoration technicians here at Bridge Classic Cars, has been busy preparing both the car and the engine for the pair to be reacquainted.

Previously, after testing the 1973 MG B GT V8 our technicians found metal shavings in the oil after it was drained as part of our testing procedures. Since then, Jonn has replaced the bearings which had been found to be deeply grooved as well as fixing a problem with the oil pickup which had caused the issue in the first place.

Since that, the engine has been prepared to go back into the front of this beautiful purple sports car.

Keep an eye out here on the Bridge Classic Cars news page for more updates very soon on the 1973 MG B GT V8.

Good as New – Sending the 1905 Riley 9HP Parts Away to be Refurbished

Bridge Classic Cars have the honour of being the current caretakers of the incredible 1905 Riley 9HP believed to be one of only three remaining in the world.

The car has many unique brass pieces which make up its antique charm. These irreplaceable pieces are being documented and catalogued ready to be sent off for refurbishment for the project. The pieces will be sent to a specialist of early brass automotive parts to be brought back to their former stunning glory.

Although the car is now 116 years old, it is an amazing reference piece for our restoration teams to look back on and see how these types of vehicle were handmade.

Falling Inline – The Story of the Jaguar XK Straight-Six

Jaguar. A legendary name in both performance and luxury. Just the name is enough to conjure images of elegant, long-legged coupes and saloons powered by the now infamous XK straight-six engine. But, what is the story behind this incredible powerhouse which lived 1000 different lives?

Debuting in 1949, the XK straight-six came with a sizeable 3.4-litre displacement, it was the brainchild of four very important icons in the Jaguar world. Sir William Lyons, William Heynes, Walter Hassan and Claude Bailey. The introduction of this engine however stretches back nearly a decade before. During World War II when the company still went under the name SS Cars, the team were actively seeking and developing replacements for its engine lineup so, during its wartime efforts they worked on the new powerplants for its post-war cars. Jaguar had begun to produce and develop the engine just after the nightmares of war had begun to subside at the end of the 1940s. The cornerstone of these engines was to be higher output, higher quality and higher style, thus the XK Inline-Six was born.

The XK engines first saw service in 1947 with the 3.2-litre units (XJ 6 Cylinder) but during testing of the engines, it was found they severely lacked low-end torque, so the blocks were bored out to 3.4 litres (XK 6 Cylinder) and were destined to be the beating heart of one of the most beautiful cars ever made, the XK120 which broke cover at the 1948 London Motor Show. This would then see the engines fitted to the upcoming MkVII’s and countless other models over its production run.

The cast-iron engine blocks were not the lightest but were highly durable. The construction techniques developed for this engine would push other manufacturers to refine and develop new and improved engines to try and match the level that Jaguar was achieving. Jaguar fitted special vibration dampers to the crankshaft of the engine to absorb and limit the number of frequencies travelling through the crankshaft and ultimately the XK’s split case engine design.

In 1951, Jaguar began work on developing the idea of a smaller displacement but still useable version of XK straight-six. The results for the 2-litre engine were mixed and by 1954 the engine had grown to become a 2.4-litre unit. The engine itself was actually shorted than the bigger displacement engines but remained under the same name and architecture. These engines would be put forward to power the upcoming stylish and sleek saloon, the MkI. The road engines were entirely carburetted until 1978 (the first year of road engines being fuel injected for the US market) but would use a combination of two or three SU’s. Webers or Zenith carburettors except for the MkII 240 which had a set of downdraught Solex units.

From this, all the subsequent Jaguar XK straight-sixes were laid out. Short block engines would make up the smaller displacements such as the 2.4 and 2.8-litre engines and the longer, more torquey powerplants would go anywhere from 3.4 to 4.2 litres by the end of its production. Jaguar officially retired the XK 6-cylinder in 1992 replaced by the newly developed AJ6 platform it used alongside the faithful XK until the AJ6 was then also retired in 1996.

During this incredible engines lifetime, it would see all manner of changes and applications. From racing to agricultural work. Le Mans to Leicester and beyond. This incredible piece of not only industrial design but of engineering excellence and durability should be remembered and revered for the legend it surely is.

Long live the XK Straight-Six.

Workshop Update – New Door in the Trim Shop

Over the coming weeks and months, there are some changes beginning to happen at the Bridge Classic Cars workshop in Pettistree, Suffolk. Apart from our new workshop extension, the changes have already started to begin.

The trim shop, where Brian and Kath create some of the most incredible automotive upholstery you have ever seen, is now accessible from our in-house paint booth and vice versa. This allows for better movement around the building and also a better flow for the restoration teams.

There are more changes coming soon to the building but you’ll have to wait and see. Keep an eye here on the Bridge Classic Cars news page for more updates on our very special workshop.

Preparing for the Next Phase – Continuing Work on the 1968 Jaguar MkII 2.4

Bridge Classic Cars have been working on preparing the 1978 Jaguar MkII 2.4 to prepare it for the next phase of work to begin.

Dave, one of our most experienced in-house restoration technicians, has been working on removing the interior and other parts of the car to begin working through the mechanical jobs on this stunning MkII. Carefully, as each piece is removed from the car, it is then catalogued and safely stored for later during its rebuild.

For now, it’s carefully assess the areas of attention for the owner and coming up with a plan to deliver the best result.

Expect to see more on the 1968 Jaguar MkII 2.4 here on the Bridge Classic Cars news page very soon.

Thorough Clean – Further Cleaning of the Engine of the 1971 Jaguar XJ6

Jonn, one of the Bridge Classic Cars in-house restoration technicians, has been working on cleaning out the engine block of the 1971 Jaguar XJ6 currently in our workshop.

In the last update, Jonn had discovered the block of the straight-six packed with brown sludge.

Jonn has been working on thoroughly cleaning out every passage inside the engine as well as cleaning up the threads of the head studs. Jonn has methodically worked his way through the entire engine from front to back, cleaning and flushing through any remnants of the dirt.

With this complete, Jonn is confident that the engine block is now completely clear and ready for the next stage of the work to begin.

Mirror Image – Bodywork on the 1977 MGB Roadster

This 1977 MGB Roadster is in with Bridge Classic Cars for a full cosmetic restoration. That does involve a bit of cutting…

Scott has worked his magic on the passenger side of this amazing sports car over the last few weeks. Carefully removing any corroded metal on its flanks so that the new wings can be grafted in and secured. Now, it was time for Scott to begin work on the driver’s side. Much the same as the other, Scott only cut where was needed to remove the material and give enough room to comfortably weld the new panels in with very little distortion from the heat.

Using a thin cutting disc, Scott managed to create clean and precise cuts to remove firstly the original rear wing and then the structure and wheel arch behind it. These are needed to be removed and replaced with brand new pieces as part of the car’s aesthetic restoration.

Now, with the wings all on and cleaned up. It’s time to move forwards.

New Arrival – 1971 Bristol 411

The Hangar welcomed its latest resident. This unique 1970 Bristol 411.

This car is being stored with us at our safe, secure and private storage facility, The Hangar, while it awaits its time at the Bridge Classic Cars workshop in Pettistree. This car has been acquired by ourselves for a customer who lives in Europe. This car will be taken to the workshops and some very special jobs to be carried out on this rare piece of British motoring.

The car itself is in stunning condition. The dark green paintwork is bright and even across its long elegant body. The interior is finished in vibrant red leather which has some marks that only add to its character and story. Overall, this is a stunning piece of automotive history which we are honoured to store and work on at Bridge Classic Cars.

Expect to see more very soon about the 1970 Bristol 411 on the Bridge Classic Cars news page very soon once this exciting project begins.

To The Smallest Detail – Preparing Parts of the 1956 Jensen 541 For Sandblasting

The teardown of components for sandblasting is a crucial step in any restoration. The parts need to be broken down into the their separate pieces in order to be properly blasted and cleaned but also different attention is sometimes required to different materials. Another part of this is knowing the fixing and the parts are in good or rebuildable order before they are sent out.

That’s why Mauro, one of our in-house restoration technicians has been hard at work carefully taking apart each of the components which will be sent away of the 1956 Jensen 541 for sandblasting. With a car as bespoke and handbill as the 541, it is important to carefully remove and catalogue all pieces that come off the car for later when the rebuild begins. Also, for reference to know exactly what is being sent out. That is something Bridge Classic Cars prides itself on with our restorations, the level of detail.

Each component, piece by piece was gently and sympathetically broke down to its constituent parts in order to be fully assessed before being labeled and photographed. These pieces will be sent to a local specialist to treat and revitalise before being returned to us at Bridge Classic Cars for the Jensen. The process allows the fresh metal underneath to breathe but also for our restoration teams to assess any imperfections or hidden damage to the components when they arrive back. As you can see with the Jensen, there are lots of parts with even more small fixings and components so it is crucial with a restoration as in depth as that of the 1956 541 that everything is as good as it possibly can be.

Expect to see more on the 1956 Jensen 541 being restored at Bridge Classic Cars very soon here on the News page.

Rock Solid – Repairing Rust Issues on the 1968 Jaguar MkII 2.4

Unfortunately, it is a problem that plagues all classic cars at some point in their lives. But, caught early enough it can be easily sorted. We’re talking about rust. The dreaded plight that rears its head on old metal. That is the case of this 1968 Jaguar MkII 2.4 which Dave has been been working on.

Previously, this car has been in with Bridge Classic Cars for some sympathetic rust repairs but now it’s time to continue. There were two areas Dave concentrated on. The spare wheel well in the boot floor and the drivers footwell.

The hole in the drivers footwell had crossed out over onto the chassis rail so, Dave has made up custom patch panels to be able to bridge the gaps safely and securely underneath the MkII. Through years of experience and skill, Dave evaluated how much of the original metal would need to be removed in order to get rid of any corrosion and also create a strong enough span for the piece. After that, Dave used as close as original thickness material to create the multi-piece patch panel for the drivers foot well. After tacking the piece in, Dave slowly moved around the panel to allow it time to cool and settle and avoid any warping which may cause interior trims to not sit correctly.

The boot floor was much the same story. Using a patch panel, Dave carefully cut only what was needed to achieve a strong bond and a stable floor. All of the exposed metal was treated and then covered in several layers of prime and matching black paint to prevent the new pieces from rusting prematurely.

Expect to see more on the 1968 Jaguar MkII 2.4 very soon on the Bridge Classic Cars news page.

Tear Down – Stripping the Bumpers of the 1955 Aston Martin DB2/4

Mauro, one of the Bridge Classic Cars in-house restoration technicians, has been stripping down the bumpers, grille and brightwork on the 1955 Aston Martin DB2/4 that is undergoing restoration at Bridge Classic Cars.

These pieces have been carefully broken down into individual components to be sent off for various treatments for them to be refinished to a standard fitting of the car. The brightwork on the Aston Martin is a key focal point to such an iconic sports car that they need to fit just right as well as look the best.

With that, Mauro has been carefully removing each bolt from the bumpers and brackets to make sure they are in good condition and if not, they are replaced. The bumpers, grille and all other parts are carefully catalogued and stored until they are ready to be sent off to local specialists that we have been working with for many years on our other world class restoration projects.

The level of detail that Bridge Classic Cars holds itself to, even in terms of the breakdown of each component, is purposely high to ensure the best final finish of our restorations.

Keep a look out here on the Bridge Classic Cars news page for more updates on the 1955 Aston Martin DB2/4 soon.

Coming Back Together – The Rebuilt Straight-Six is Back for the 1963 Jaguar MkII 3.4

The straight-six for the 1963 Jaguar MkII is back and is in the car. Some of you may remember from it’s last update, some damage was found on inspection of the internals of the engine so it was sent away for a rebuild.

The engine has been gone through thoroughly to ensure all is ok before it went back into the car. Paul, one of our in-house restoration technicians, has fitted the glorious 3.4 litre straight-six back into the front of the stunning white MkII.

The accessories will be refit into the car and testing will begin by our in-house technicians to ensure the engine and the issues noted have been rectified.

Another Step Forward – More of the Interior of the 1973 Jaguar E Type Series III Roadster

Fern Grey, the 1973 Jaguar E Type Series III Roadster, is a very special car. Not only has the car itself been hand built from the ground up, but its entire interior has too. The Bridge Classic Cars in-house trim shop are truly world class. Brian and Kath’s team deliver handcrafted, bespoke interiors for our customers.

That is the story of the interior of Fern Grey. Kath and Brian have been working on getting more of the sound deadening into the car, while also fitting out the rear panels in preparation for the rear covering.

The sound deadening is being placed down where there will either be considerable road or driveline noise. The point of Fern Grey is to be a Grand Tourer like the E Type was always intended so part of that easy living is making sure cabin volumes is kept to a minimum where possible. The sound deadening material lays down perfectly flat after Kath and Brian make templates for each individual pieces, making sure it does not interfere with any piece of the custom made interior.

The rear panels are a work of art. Carefully covered in the signature green leather of Fern Grey are the quarter panels that overlap one another. A lot of time, care and attention has gone into these panels purely due to where and how they fit into the car. Kath must have test fit these panels 20 times before the final installation of them.

Next up for Fern Grey, Kath and Brian will be beginning to lay the custom carpet pieces into the bottom of this incredible one of E Type.

Finer Details – Painting the Headlight Covers for the 1934 MG PA Midget

Chris has got the latest pieces for the 1935 MG PA Midget in the Bridge Classic Cars paint booth. These are the new headlight covers for the 1934 MG PA Midget!

The MG PA will be getting colour matched headlight covers that Chris has worked hard to try and colour match to the rest of the amazing early sports car. Chris prepped the pieces thoroughly to make sure that during the primer and colour coats it would lay evenly and match the finish of the existing paint on the car.

They look absolutely phenomenal. Once these have cured, they will be handed our to our in-house restoration technicians to begin fitting them to the car as they work their way through the list of things to do on this amazing car.

Coming Soon – 1975 MGB GT V8

Coming soon to the Bridge Classic Cars workshop here in Pettistree, Suffolk is this stunning red 1975 MGB GT V8.

The car will arrive and then be assessed by our various in-house restoration experts to determine what needs doing and in what order to make this amazing British sports car as good as new.

Keep an eye out on the Bridge Classic Cars blog for more on the MGB GT V8 once it arrives.

Making Headway – New Panels on the 1977 MGB Roadster

Scott, one of our incredible in-house restoration technicians here at Bridge Classic Cars, has been working on getting the new inner and out rear quarter panels fitted onto the 1977 MGB Roadster.

This process is best-done inch by inch when it involves the removal of inner body panels. The rear wings, needed to be replaced so the best quality replacement wheel arches and rear quarter panels were sourced for this car. After removing the pieces from the car carefully, Scott could then begin to test fit and trim the new panels into the car. A job where precision, accuracy and a steady hand are crucial but that is something we pride ourselves on here at Bridge Classic Cars.

With the panels now cut to size and shape, Scott methodically welded the new pieces into the Roadster so as to not warp the shape on the pieces. Then, that was one side of the car done and just the other side to go!