1968 MG C

Small Changes – Upgrades to the 1968 MG C Roadster

The workshop team at Bridge Classic Cars are working on some wiring upgrades to the 1968 MG C Roadster along with a couple of wiring issues sorted out alongside it.

The team will also be rechecking several systems for the owner and running some other wiring checks to get to the bottom of a few issues.

Adjustments – Adjusting the Carburettors on the 1968 MGC Roadster

The 1968 MGC Roadster is being worked on by the Bridge Classic Cars in-house restoration team to get the classic sports car running just right.

After road tests, the car was running slightly off so Jon set about adjusting the carburettors to get the 6-cylinder running perfect. Upon inspection, he found that 2 out of the 3 carburettors were flooding and allowing too much fuel into the chamber. After adjusting the rest floats, Jon could then work on adjusting and synchronising all 3 carburettors together and ran the car to check the issue had been rectified.

Updates – Fitting New Warning Lights, Fuel Pump and Washer Pump to the 1968 MGC Roadster

The workshop team at Bridge Classic Cars have been working on getting through the list of jobs on the 1968 MGC Roadster.

The latest work to be completed on the car is the new addition of hazard lights fitted into the lower centre console of the classic convertible before specifically made blanks were installed in order to cover up any previous holes.

Along with that, Jon has run the wiring to change the switch for the washer pump from the original stork style to the newest switch style and fitted a new washer pump along with it.

At the back of the car, the team have installed a new fuel pump onto the car to sort out some fueling and idling issues with the car. Also, this has been installed as a matter of course to help with the longevity and ease of use of the car.

Soundtrack – Fitting the Stereo and Speakers to the 1968 MGC Roadster

The 1968 MGC Roadster in the Bridge Classic Cars restoration workshop has had its new stereo and speakers installed into the interior of the classic convertible.

Jon has been working on carefully running the wiring throughout the car from the rear pillars under the carpets and inside of the centre console to the new head unit for the stereo. With all of the wiring run, Jon could work on getting the head unit into place and wired up to the speakers to begin testing it.

Careful Cutting – Working on the Clock & Radio Panel of the 1968 MGC Roadster

The trim shop at the Bridge Classic Cars Suffolk HQ have been working on finishing up the interior of the 1968 MGC Roadster.

Brain, one of our trimmers, has been carefully cutting out a new hole to fit up the new clock into the dashboard of the classic and rare MGC. The panel had to be clamped down and the new wood veneer laid over the top to use as a template to mark out the piece.

Once the piece had been marked out, Brian carefully drilled out the new clock opening and finished it by hand. Now that this was complete, he could begin to secure the veneer to the panel.

After the adhesive had cured completely, he could fit the panel into the car and secure everything down into the car.

Fit and Finish – Interior Trim on the 1968 MGC Roadster

The trim team at Bridge Classic Cars have turned their attention back to the interior of the 1968 MGC Roadster.

Brian has been renewing the wooden veneers which cover the face of the dashboard as well as the centre console. After these were all secured in place, it was the job of carefully refitting all of the trim pieces and brightwork back into place on this truly beautiful and rare MGC Roadster.

Stripped Back – Removing the Wood Panels on the 1968 MGC Roadster

The 1968 MGC Roadster is now in the hands of the Bridge Classic Cars trim team who have been working on refinishing the wooden panelling on the interior of the MGC.

Brian carefully removed the veneer on the dashboard and centre console piece by piece to strip the panels back to their most basic. He also removed the radio blanking plate as well as several gauges in order to get access and check over.

Update – Progress on the 1968 MGC Roadster

The 1968 MGC Roadster in the Bridge Classic Cars restoration workshop at our Pettistree HQ has had a series of key jobs finished on the classic roadster.

Jon has been working on getting the MGC Roadster sorted for its new life. Ranging from the engine bay, under the dash and the wheels.

The first job was to fit up the new hoses which lead to the breather tank in the engine bay of the car. This is vital that any excess oil or any fumes are routed into a separate tank. There are several vent tubes associated with the 6-cylinder engine that are required to be routed to the catch can.

Next, he began to look into getting the heater cable fixed in place and linked up to the controller/dial on the dashboard of the MGC. With everything linked up, Jon could test the heating system in the cabin of the classic MGC.

A crucial job that needed to be done on the car was replacing one of the wheel bearings. Jon noticed that the wheel was making some small noises and allowed for some small movement back and forth when rocked.

With all of this done, the car can be completely road tested and signed off.

Neat and Tidy – Tidying Up The Engine Bay Wiring of the 1968 MGC Roadster

The restoration technicians in the Bridge Classic Cars workshop have the fantastic 1968 MGC Roadster currently on the ramp to complete several jobs on the car. This time, it’s tidying up the wiring in the engine bay.

Jon has been methodically going through the wiring under the bonnet of the classic convertible sports car to make sure everything not only works correctly but is safely routed around the engine bay. System by system, he has grouped together separate parts of the harness and shielded them where necessary.

Adjustments – Adjusting the Door Handles and Rear Lights on the 1968 MGC Roadster

The workshop at the Bridge Classic Cars Suffolk HQ have been working on the 1968 MGC Roadster.

Our technician Jon has been getting a series of jobs completed on the rare roadster ahead of its departure from the workshop. Jon has been adjusting the door handles for the car and realigning the strikers so that when the handle is pulled or the door is pushed back into place there’s no binding up of any of the mechanisms.

He has also been making sure all of the rear lights are secured into the car and that each and every function of the clusters works just at it should do.

Early Rising – Collecting a 1968 MGC Roadster from the Port

In the latest Bridge Classic Cars film, join the team as they travel to the Port of Harwich to collect a very rare and sentimental 1968 MGC Roadster arriving from Germany and bring it all the way back to our Suffolk HQ.

If you haven’t already, remember to head over to our YouTube channel and like, comment and subscribe.

The State of Things – Wiring Repairs on the 1968 MGC

The Bridge Classic Cars in-house restoration team have been working on the 1968 MGC that arrived at our Pettistree workshop at our Suffolk HQ.

Our in-house technician Paul has been going through the incredible sports car and found some damage to the wiring harness. So, Paul has been methodically repairing the affected wires and carefully reshielding them after testing them thoroughly.

With this done, Paul can begin checking the other systems on the MGC.

This Just In – 1968 MGC

The Bridge Classic Cars restoration workshop in Pettistree, Suffolk has recently welcomed this glorious 1968 MGC.

This car will go in for our in-house restoration technicians to assess the entire vehicle to see what may need doing to this fantastic and rather rare sports car.

The MGC is a 3 litre straight-six powered MG Roadster built between 1967 and 1969. This is one of 4542 Roadsters built during its entire production run.